English
Espaol
Franais
阿拉伯
中文
Deutsch
Italiano
Português
日本
韓國
български
hrvatski
esky
Dansk
Nederlands
suomi
Ελληνικ
印度
norsk
Polski
Roman
русский
SvenskaJohn Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法供應商，John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法技術價格規格咨詢服務，John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法零配件供應，John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法售后服務中心，John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法，John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法詳細的技術參數，
首頁
產品展示>John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法
產品中心
美國強鹿柴油機維修配件技術中心
約翰迪爾John Deere柴油機配件 美國麥克福斯
卡特彼勒柴油發動機參數
沃爾沃發動機全系參數
英國珀金斯原廠配件
珀金斯柴油機技術中心
珀金斯發動機零件查詢圖冊
日本三菱柴油機發電機配件
德國道依茨 韓國大宇柴油發動機配件
康明斯全系列柴油發動機
沃爾沃 MTU 原廠配件銷售中心
瑞典沃爾沃遍達原裝柴油機配件
康明斯維修技術中心
卡特彼勒柴油發動機原廠配件銷售中心
品牌柴油發電機組
康明斯柴油發動機配件中心
John Deere約翰迪爾強鹿4045柴油發動機氣門間隙的檢查和調整方法
詳細描述
檢查和調整氣門間隙
John Deere約翰迪爾強鹿4045 柴油發動機氣門間隙的檢查和調整方法
1. Remove rocker arm cover and crankcase ventilatortube.
IMPORTANT: Visually inspect contact surfaces ofvalve tips and rocker arm wear pads.Check all parts forexcessive wear,breakage, or cracks. Replace parts thatshow visible damage.Rocker arms that exhibit excessivevalve clearance should be inspectedmore thoroughly to identify damagedparts.
2. Remove plastic plugs or cover plate from enginetiming/rotation hole (A) and timing pin hole (B).
NOTE: Some engines are equipped with flywheelhousings which do not allow use of an engineflywheel rotation tool. These engines with straightnose crankshafts may be rotated from front noseof engine, using JDG966 Crankshaft Front/RearRotation Adapter.
3. Using JDE83 or JDE81-1 Flywheel Turning Tool, rotateengine flywheel in running direction (clockwise viewedfrom front) until No. 1 cylinder is at TDC compressionstroke. Insert JDG1571 or JDE81-4 Timing Pin inflywheel.
If No. 1 cylinder rocker arms are loose, the engine is at
No. 1 TDC compression.
If No. 1 cylinder rocker arms are not loose, rotateengine one full revolution (360°) to No. 1 TDC
4. With engine lock-pinned at TDC of No. 1 piston’scompression stroke, check valve clearance to followingspecifications. (Use sequence for 4-cylinder or6-cylinder engines as outlined on next page.)
Specification
Intake Valve Clearance Checking(Rocker Arm-to-Valve Tip)(Engine Cold)—Clearance 0.31—0.38 mm(0.012—0.015 in.)
Exhaust Valve ClearanceChecking (Rocker Arm-to-ValveTip) (Engine Cold)—Clearance 0.41—0.48 mm(0.016—0.019 in.)
5. If valves need adjusting, use the appropriate valveclearance adjustment procedure on the next page andadjust to specifications below. Loosen the jam nut (A)on rocker arm adjusting screw. Turn adjusting screwuntil feeler gauge slips with a slight drag. Hold theadjusting screw from turning with screwdriver andtighten jam nut to specifications. Recheck clearanceagain after tightening jam nut. Readjust clearance asnecessary.
Specification
Intake Valve ClearanceAdjustment (Rocker Arm-to-ValveTip) (Engine Cold)—Clearance .................................. 0.36 mm (0.014 in.)
Exhaust Valve ClearanceAdjustment (Rocker Arm-to-ValveTip) (Engine Cold)—Clearance .................................. 0.46 mm (0.018 in.)
Specification
Rocker Arm Adjusting Screw JamNut—Torque .................................................................... 27 N•m (20 lb-ft)
6. Install rocker arm cover and crankcase ventilator tube.